When To Replace Dirt Bike Brake Pads?

(As an Amazon Associate DirtBikeIdeas.com earns from qualifying purchases)

When To Replace Dirt Bike Brake Pads? If you race motocross or ride your dirt bike at a fast pace, then you will need to replace the brake pads more often than someone who prefers slow trails and low speeds. Dirt bike brakes are designed to work at high temperatures so when they heat up from braking hard and long, it is time for fresh brake pads! Here is a list of signs that it is time to replace dirt bike brake pads.

When To Replace Dirt Bike Brake Pads – Deciding Factors

1) How Old are Your Brake Pads?

There are no standards when it comes to the expiration date for dirt bike brake pads, so you will have to decide when they are too old. Most manufacturers recommend replacing brake pads after one or two riding seasons, even though this is a conservative approach. If you have not used your dirt bike in a while, then the brake pads were most likely left sitting and gathering dust on a shelf somewhere rather than being exposed to hot temperatures. Dirt bike brake pads can also be damaged from extended periods of non-use; therefore, they may need replacement more often if you don’t ride often.

2) When Dirt Bike Brake Pads are Worn Out, Cracked or Rotted

If the metal backing of the brake pads is exposed, they will need to be immediately replaced because dirt particles can get inside of the breaks housing and cause additional damage. The metal shavings can also wear away at other vital components, so don’t play around with this! If the brake pads are cracked to the point of being unsafe, then they must be replaced. Dirt bike brake pads can also be rotted away from exposure to moisture if they are not fastened down properly so don’t neglect your dirt bike brakes!

3) When Dirt Bike Brake Pads are Worn Thin

If your dirt bike brake pads are thin, then they should be replaced because not only will they wear out quickly, but you also run the risk of not being able to stop in time. Pads that are worn thin will need to be replaced immediately to ensure that your dirt bike brakes are working correctly.

4) When Dirt Bike Brake Pads are Worn Smooth or have Gaps in Tread Pattern

Although brake pads are normally thicker than the tread on your dirt bike tires, they will eventually get worn down to a smooth surface. If you can feel deep grooves in the pad when braking, then they need to be replaced because any weak points will send metal shavings into other brake components that can cause damage. You may also notice small gaps across the front of the pad that leaves tread marks on your dirt bike tire if it is time for new brake pads. If you bend over and look at the front of your dirt bike brake pads closely when riding, this should help you make an informed decision about whether or not they are worn out.

More to Read: What is a power band in dirt bike?

How do I know if my motorcycle brake pads are worn?

Typically, you will not be able to see the brake pads without removing the wheel. However, there are plenty of other indications that your dirt bike brakes need replacing. For example, if you pull on your front brake lever and it feels soft or spongy rather than firm then this is a sign that you should buy new dirt bike brakes soon before an accident occurs! If your dirt bike has a rear disc brake only, then all you have to do is inspect the rotor for any signs of scarring or rusting because this can indicate that it is time for new dirt bike brake pads.

Replacing Dirt Bike Brake Pads When Changing Tires

If you also change tires when servicing your dirt bike, then be sure to replace worn-out dirt bike brakes to avoid any problems while riding. If you change both the front and rear tires at the same time, then it is a good idea to replace dirt bike brake pads on both sides of your dirt bike because this will ensure that they work equally well when needed.

How do I install Dirt Bike Brake Pads?

First, use a screwdriver to remove the old dirt bike brake pads from the caliper assembly. Then take a look at how they are fastened down so you can properly secure new ones in their place. Dirt bike brake pads have an arrow pointing forward or “front” marking on them so they should face up when installed correctly. Next, take some high-temp anti-seize lube and spread it on the metal contact area of the new brake pads. Insert your new dirt bike brakes into place and secure them with a screwdriver so they won’t move while you put the wheel back on.

Different Types of Brakes

There are two basic types of brakes used in dirt bikes.

1) Disk Brakes

The first is the “disc brake” design, which uses a rotor to slow down your dirt bike. As you pull on the hand levers, pads are squeezed together and firmly press against the rotor to slow down and stop your dirt bike quickly.

Types of Disk Brake Pad

i. Metallic or Sintered

Metallic or sintered disk brakes are designed to last longer than organic types because they are harder. However, sintered pads also tend to be noisier and produce more dust when applied.

ii. Organic or Non-Metallic Brake Pads

Organic or non-metallic disk brakes contain carbon fibers that help dissipate heat away from the brake assembly which results in less fading during long rides on your dirt bike. This type of brake pad is also softer so it will wear out faster but perform better if you are riding aggressively off-road.

iii. Natural or Resin

Natural or Resin brakes are a variant of organic brakes that use a softer material composed of natural fibers with resins applied for strength. They perform well in all riding conditions and are safe to use when wet. They also have a smooth feel to them and are easy on other components because they don’t leave deposits from braking friction.

2) Drum Brakes

The second type of brake found in most dirt bikes is called a “drum brake”. Instead of using a rotor as disc brakes do, drum brakes rely on metal shoes (brake pads) that expand outward and press against the inside of an enclosed drum to slow down your dirt bike. Although drum brakes typically need more maintenance than disc brakes because they use rubber brake shoes, they offer increased stopping power for heavy loads or high-speed riding.

As long as you consistently replace worn-out brake pads before they create any additional problems, your dirt bike should not have any problems stopping whenever you need it to.

What Happens If You Do Not Replace the Brake Pads?

If you do not replace the dirt bike brake pads, it can cause trouble for your brakes and may lead to costly repairs if not timely replaced. Especially if you have a front disc brake, dirt bike brake pads should be checked regularly for any wear or damage because this part is responsible for slowing down your dirt bike when stopping.

Replacing the front or rear dirt bike brake pads can fix any existing problems with your hydraulic braking system without costly replacement of the entire assembly. So it only makes sense to replace worn-out dirt bike brakes before they become a danger to you and others who ride with you.

Dirt Bike Front Brake Assembly

How long does a motorcycle brake pad last?

Dirt bike brake pads last for 20,000 and 30,000 miles before they need to be replaced. So if you ride your dirt bike regularly, you will probably need new brake pads at least two or three times per year.

Replacing dirt bike brake pads is easy once you know how to do it. Just remove the wheel of your dirt bike first so you can access the caliper assembly. Then simply remove each brake pad one at a time by taking off any screws that are holding them down into place. Dirt bike brake pads are fairly inexpensive and cost between $25 to $40 for most models. Find Some Best Brake Pads Here!

As long as your motorcycle brakes are working properly, you should have no problems safely stopping whenever necessary whether on the street or on an ATV trail!

dirt bike Brake Pads Installation

What are the best brake pads for motocross?

There are different factors to consider to choose the brake pad as the best of all. It should be semi-metallic, not much expensive, has high wear and tear resistance, should have to be sufficient harder for rotors. If you are looking for a brake pad with all of these options, I would suggest a semi-metallic brake pad. They are not much expensive, will wear out easily, and are harder on the rotors.

How do I separate my dirt bike brake pads?

You will have to be very careful while removing the brake pads. Avoid using any hard or sharp thing like a screwdriver. Screwdrivers are very hard and they can easily damage the brake pads. Use something of plastic, a plastic lever would be the best. You can also use some sort of piston press tool to separate the brake pads gently.

How long will 7mm brake pads last?

7mm brake pads are the best option. They last for longer. If you are using brake too much, a 7mm brake pad will last for more than a year.

What are the signs of worn brake pads?

Here are some signs of worn-out brake pads. There are various pointers that can hit the alarm, and you will have to change your brake pads.
-Squealing noise
-Clicking noise
-Loose brakes
-Takes more time to stop
-Vibration of pedal

Final Verdict

We will close our article by offering you one final piece of guidance: Check your brake pads frequently. Considerably more so in case you are a genuine cyclist. Plate brake pads typically last more than edge brake pads. Indeed, even with steady cycling, a couple of brake pads can last you months. They are modest to supplant. Remember all the points we have adopted today. You ought to be better mindful of the well-being of your bike’s brake pads.

If you’ve noticed that your brake pads are starting to wear out or if they’re making a high-pitched screeching sound, it’s time for new ones. And if the dirt bike is giving off an unusual smell when braking, it could be due to oil on the brakes and needs some attention. When replacing dirt bike brake pads with us at DirtbikePartsUSA.com, we’ll make sure all of the components look great and work well together so everyone can enjoy their ride safely!

Leave a Comment